• Nail Wraps
  • ColourCure
  • TruShine
Application & Removal

Nail Wraps

How To Apply

  1. Nail Prep: Push back cuticles. Buff and clean nails with a Nail Prep Wipe or Nail Prep Cleanser.
  2. Match nail wrap that best fits your nail. Err on the smaller size to avoid overlapping on the skin/nail edges, which can cause lifting.
  3. Cut nail wrap in half, pick up wrap from the cut side with an orange stick, and peel away from clear backing sheet.
  4. Warm the adhesive side of nail wrap with a Mini-Heater or blow dryer for about 3 seconds. Avoid overheating.
  5. Press nail wrap onto nail with the rounded edge at the cuticle. Firmly smooth the nail wrap down the center of the nail toward the tip. Next, smooth the sides starting at the center and toward the edges to seal the nail wrap to the nail.
  6. Trim excess with nail scissors. File off remaining nail wrap using a downward motion.
  7. Apply heat and pressure to the nail wrap until it is bonded to the nail.

How To Remove

  1. Soak the nail wrap in our Nail Wrap & Lacquer Remover for 20-30 seconds.
  2. After soaking, gently peel the nail wrap from side to side.
  3. Finally, apply Cuticle Oil for a winning finish!


Application & Removal

ColourCure

How To Apply

  1. Wash hands with warm water and dry completely.
  2. Trim or file nails and push cuticles back with cuticle pusher and lightly buff nails with buffer block.
  3. Clean nails with Nail Prep Cleanser or Nail Prep Wipes.
  4. Carefully apply a thin layer of ColourCure starting near the base of the cuticle, leaving a slight gap between the product and your skin. Immediately clean any excess ColourCure on the skin or around the nail plate with an orange stick.
  5. Cure with ColourCure UV/LED Curing Lamp for 120 seconds (or three cure cycles with TruShine Curing LED Lamp)
  6. Apply a second thin layer of ColourCure—starting near the base of the cuticle leaving a slight gap between the product and your skin. Clean any excess ColourCure on the skin or around the nail plate with an orange stick.
  7. Cure with ColourCure UV/LED Curing Lamp for 120 seconds (or three cure cycles with TruShine Curing LED Lamp)
  8. Allow ColourCure to finish curing in natural light for 60 seconds before touching.
  9. Wash hands with soap and warm water and dry completely.
  10. NOTE: DO NOT wipe the nail with Nail Prep Wipe after curing. The sticky residue will disappear while formula is polymerizing.

How To Remove

  1. The most efficient way to remove ColourCure is to fill a small bowl with Jamberry Nail Wrap & Lacquer Remover and soak your nails for 3 minutes.
  2. After soaking your nails, wipe clean with a cotton pad or similar product. You can also use the TruShine Remover Pockets to soak-off ColourCure (takes 5-7 minutes typically).
  3. Apply Cuticle Oil for happy, healthy nails.


Application & Removal

TruShine Gel

How To Apply

  1. Nail Prep: Push back cuticles. Buff and clean nails with a Nail Prep Wipe or Nail Prep Cleanser.
  2. Apply a thin layer of base coat starting at the cuticle. Then, lightly brush over the tip of the nail to create a seal. Cure with TruShine LED or ColourCure UV/LED Lamp.
  3. Polish on a thin layer of your favorite gel shade starting at the cuticle and lightly brushing over the tip of the nail to create a seal. Cure and repeat with a second Color Coat.
  4. Seal nails with TruShine Top Coat and cure.
  5. Use a Nail Prep Wipe or Nail Cleanser to remove gel residue. Apply cuticle oil and enjoy a flawless look for up to two weeks!

How To Remove

  1. Tear open the Remove Pocket and remove the clear protective plastic to expose the adhesive strip.
  2. Insert your finger so that the nail is in direct contact with the pad. Fold the pocket in half and press the adhesive strip onto itself to create compression.
  3. Leave pocket in place for 10-15 minutes.
  4. Using an orange stick, gently slide off the flaked gel enamel. If excess gel still remains, place your finger back into the pocket and check again in 2 minutes.
  5. Finally, apply Cuticle Oil for a winning finish!